Clear Bra Kits, 3M Paint Protection Film pre-cut patterns

Clear Bra Kits For Cars, Trucks, Vans, SUV’s & Motorcycles

3M Ventureshield paint protection film kits

3M Ventureshield Clear Bra Kits available for nearly every make and model of vehicle. If you have a car, truck, van, SUV, motorcycle or any other painted surface and you would like to protect it from being damaged. Clear Bra Kits has the film and patterns to protect that area. The most common areas to protect on a vehicle would be the hood, fenders, mirrors, front bumper and headlights. However we offer clear bra patterns for a lot of other areas. Some of these areas such as the rocker panels, the top of the rear bumper, roof a-pillar, full hoods, doors, and gas flap areas are also an option.

2010 Ferrai F430 Clear Bra Installation

The first step in the clear bra kit installation is to prepare the surface area. We recommend that you first clear the hood with a 3M adhesive remover. Next in a 32oz spray bottle mix 5oz of alcohol the rest water. Then clean the hood with alcohol and water soulution. This step is to make sure you have removed all of the 3M adhesive remover.

2010 Ferrai F430 Clear Bra Installation

The next step in the Clear Bra Kit installation process is to mix the slip solution. Mix 32oz of water with 3 small drops of baby shampoo. You want enough slip so that the clear bra kit moves around on the painted surface but doesn’t fall off of the car.

2010 Ferrai F430 Clear Bra Installation

After the kit has been rolled on the vehicle you should position the clear bra kit so that all of the edges are equal and aligned. This is the step in the installation process where you should pay extra close attention to the detail of the kit. If it is aligned correctly you shouldn’t have to stretch it so much to get it to fit.

2010 Ferrai F430 Clear Bra Installation

Once the Clear Bra Kit is centered spray the alcohol solution under the hood in the center of the of the kit. Remember to spray a lot of solution both under and on top of the kit. Then apply a squeege and go top to bottom to tack the clear bra kit on the hood.

2010 Ferrai F430 Clear Bra Installation

Spray alcohol under and on top of the left side of the hood. Then gently push the clear bra kit over to the side paying extra attention to the line of the kit.

2010 Ferrai F430 Clear Bra Installation

Apply overlapping squeegee strokes starting in the center and top of the kit. Gently push the tack solution out out. This part of the clear bra installation is where you need to keep the kit extra wet to avoid scratching and stretch marks.

2010 Ferrai F430 Clear Bra Installation

Duplicate the Clear Bra Kits Installation process the same on the right side of the hood. If the kit doesn’t seem correct you can pick the film up and re-spray it with the soap and water solution and repeat the tacking process.

2010 Ferrai F430 Clear Bra Installation

Duplicate the clear bra kit installation process on the right side of the hood.

2010 Ferrai F430 Clear Bra Installation

It is important to match up the Clear Bra Kit prior to rolling it on the car. It gives you a good idea of how the kit was designed and where you might want to start. The next step in the process is to back roll the Clear Bra kit. Start by rolling the kit backwards from right to left this will mean you are starting out with the film being applied on the left side of the car. See image below.

2010 Ferrai F430 Clear Bra Installation

Start from left move to right. Make sure you have sprayed the areas with your soap and water solution.

2010 Ferrai F430 Clear Bra Installation

Gently pulling the clear bra kit backing away from the kit as you are rolling the film onto the vehicle.

2010 Ferrai F430 Clear Bra Installation

Next peel the clear bra kit off of the car while spraying your soap and water solution under the kit. You are trying to keep the adhesive from sticking to the vehicles paint. Spray only enough slip solution under the film to keep it sliding around.

2010 Ferrai F430 Clear Bra Installation

Check the alignment of your clear bra kit on the fender as you are spraying it with soap and water.

2010 Ferrai F430 Clear Bra Installation

Clear Bra Kit Fender Installation

2010 Ferrai F430 Clear Bra Installation

After the slip solution has beed applied under the clear bra duplicate the steps from the hood installation. Center the fender and spray your tack solution under and on top of the paint protection film.

2010 Ferrai F430 Clear Bra Installation

Spray your tack solution under the fender kit. Gently stretch the kit into place watching the alignment closely. Apply overlapping strokes to squeege all of the fluid out from under the film.

2010 Ferrai F430 Clear Bra Installation

Pay close attention to the alignment. If you need to pull the kit back just spray it with soap and water and repeat the alcohol process.

2010 Ferrai F430 Clear Bra Installation

Once the clear bra kit has been installed inspect you alignment and wipe the vehicle down with a micro fiber towel to make sure you don’t have any bubbles.

This clear bra kit was cut on a Graphtec plotter using our state of the art software to ensure the very best clear bra kit on the market. With this type of equipment and software, we can assure you will get an exact fit every time. All of our clear bra kits are cut using 3M Ventureshield paint protection film.

We offer Clear Bra Kits for the following manufactures:

Audi, Acura, Aston Martin, Bentley, BMW, Buick, Cadillac, Chevrolet, Chrysler, Cobra, Dodge, Ferrari, Ford, GMC, Honda, Hummer, Hyundai, Infiniti, Jaguar, Jeep, Kia, Lamborghini, Land Rover, Lexus, Lincoln, Lotus, Maserati, Mazda, Mercedes, Mercury, Mini, Mitsubishi, Nissan, Noble, Pontiac, Porsche, Rolls Royce, Saab, Saturn, Scion, Subaru, Toyota, Volkswagen.



 

 

 

About Bravo

Clear Bra and Window Tinting Shop, Minneapolis MN
This entry was posted in Clear Bra Kits 3M, Ventureshield, Paint Protection Film Kits. Bookmark the permalink.

Leave a Reply

Your email address will not be published. Required fields are marked *